Item specifics
Condition: |
New |
Brand: |
MAIYU |
Manufacturer Part Number: |
2ycn/swb3/CR/CVMB/CU/Fplt/4sq |
This listing is for a Voltmeter, 3.1 Amp dual USB charger, 12 volt accessory socket, Illuminated SPST switch and a quad mounting plate, Interconnecting jumper wires and mounting screws. #2ycn/swb3/CR/CVMB/CU/Fplt/4sq
Ships from the USA.
Daisychain jumper wires when combined with the switch allow you to connect up the elements and amke one connection to your battery.
Marine Grade 12 Volt Power Socket
For Motorbike Car/Boat/ATV/UTV/Camper/Caravans/ Travel Trailer etc
Specifically designed for marine and motorcycle applications
UV stabilized nylon housing with rubber splash proof tight fitting front cap
2 pole nickel plated brass terminal connectors. 0.250 male spade type.
Twist-and-Lock locking socket, allows a suitable power plug (not included) to lock into place. Works wth all 12 volt accessory plugs.
Rated for 15 amps at 12 volts peak 20 amps. draws no power when not in uses.
Dual USB Charger
Comes with front cap and heavy duty construction.
UV Nylon Body.
Suitable for interior or exterior use.
Suitable for charging GPS, IPhone, IPod, Mobile Phones and other digital devices
Specification:
2 port USB Socket
Waterproof Design
Power Input: DC 12V-24V
USB Socket I Power Output:DC 5V 1A
USB Socket II Power Output: DC 5V 2.1A
Output: 5V 3.1A DC(Total
Waterproof USB Cap
DC Voltmeter
Display: segment LED digital tube, lamp display is blue, red available upon request.
Monitors the state of your battery between full charged and discharged
Can indicate a poor or bad charging system. Tells whether your battery is holding a charge or not
The meter has easy to read LED segments and connect to your 12 volt system.
The meter draws nominally 10 ma. and the range is 0-35 vdc.
The switch
Splash proof front and back. Blue (Red available upon request) Illuminated Waterproof Rocker Switch -SPST. Nylon threaded switch housing mount in a 1-1/8" hole. Can be mounted in panels or dashboards up to 1-1/4" thick with the retaining nut and in panels of unlimited thickness with the mounting plate. Rated for 16 amps at 12 volts. IP rating 63. Has male ¼" crimp style disconnect terminals. Illumination is low intensity for easier night vision. Three wire connection:
Black / Green wire goes to negative 12 volt power source.
Yellow wire goes to one side of the load being switched.
Red /Brown wire goes the positive side of the load being switched.
The quad plate
The four devices mount in individual 1-1/8" holes, in panels of unlimited thickness, an optional nylon retaining nut can be used to holds the devices in place on panels of less than 1-1/2" thick. See Drilling template for mounting dimensions.
The mounting plate fits over the front of the devices to hold them against panel or dashboard. Held in place by four black screws included.
Option:
- -Add a triple segmented daisy chain jumper to this assembly. Allows you to hook up all three socket elements and make one connection to your power source. See 121464089505
-Add a USB plug connector boot. This is a vinyl boot that slips over your USB cable connector such that when the connector is inserted into the socket the boot covers the connection from weather. See item 110966193186
-Add a socket boot to increase the weather resistance of the socket. The boot covers the the wire contacts and has an exit for the wires. The socket boot may be purchase one per assembly when you buy this item. For a straight boot (shown above but not included in this listing) see this listing 120941435675. For a right angle boot for tight installations see this listing 110791911918 .
-Add a fuse holder to your socket installation. Always connect the socket to your battery with a fuse in between. This listing is for an inline waterproof fuse holder and a 15 amp ATO fuse. See listing 110968445581
-Add a rubber occlusive sealing socket washer. Makes an extra waterproof seal when mounting the socket against a panel. The washer goes between the socket flange or nut, and the panel to seal the assembly. See listing 301066433426
-Add wires with a fused 60 inch (5ft) wire harness to your socket assembly. The harness comes with of a fuse holder and fuse, and red and black wire connectors to attach to your socket and battery. See 121264213736.
-Extended warranty. This product comes with a one year warranty for damage during normal use. Just return it for repair or replace. If you want to extend the basic warranty period to three years, buy this option 301125941663
-Add a socket switch waterproof-Single pole single throw (SPST). Rubber switch cover and sealed back fits in a socket hole. Wire crimp connections. See 121422944323.
-Add extra mounting plate black screws. Allows you to mount your socket with plate in a panel of unlimited thickness. See 121435313871
-Add a mounting hole bore. Allows you to drill or enlarge a hole in your panel or dash to mount this product. See 121486220109.
-FREE FREE FREE domestic shipping on these options when you buy the item in this product listing. Just buy this listing and the options you need at the same time. Then send us a message after, to combine shipping and we will refund your shipping for the options. Applies to one of each select option only when purchased together.
-Add a Magic Socket Mounting Plate Stainless Steel Washer Assembly- with the Magic Washer the socket mounts in front of the plate and is held in place with the socket nut so the assembly becomes unified. Now the assembly is free standing and may be mounted as a free standing panel in any size opening. Buy 121555660699.
-Add a heavy paper, actual size mounting plate, drilling template set to your purchase. Allows you to position the location of the holes that need to be drilled for your installation.
Contact person:Evian Huang
website: http://dgmaiyu.en.made-in-china.com
Audited Supplier 
){kind=link}